Investigation of The Effect of Borosintering Process on Various Properties of Iron-Based Materials

Autores

DOI:

https://doi.org/10.4025/actascitechnol.v47i1.73252

Palavras-chave:

Wear; iron; powder metallurgy; borosintering; boriding; microhardness.

Resumo

In this study, samples prepared by pressing iron-based powder mixtures were divided into two different groups; sintering and boriding processes were applied in two steps in some of the samples, and in a single step in some of them. Sintering and boriding processes were applied at 950, 1000 and 1050°C for 2 hours. Various properties of borided and unborided samples in the first group and borosintered samples in the second group were compared. The microstructure in the samples was examined by optical microscope and SEM. Elemental analysis was performed by EDX. Phases formed as a result of boriding were detected by XRD. Surface roughness, microhardness measurements and wear tests were conducted on the samples. In the samples produced by powder metallurgy, the specifications of the structures formed as a result of first sintering and then boronizing process were similar. In both cases, the microhardness values of the material increased and wear-resistant structures were formed. It has been observed that the properties of the resulting structures show some changes depending on the temperature.

Downloads

Não há dados estatísticos.

Referências

Aksöz, S., Bostan, B., & Kaplan, Y. (2021). An Investigation on the Effects of Boronizing Process on Microstructure and Microhardness of NiTi Alloy Produced by P/M Technique. Journal of Polytechnic, 24(2), 539–544. https://doi.org/10.2339/politeknik.717251

Alt?nta?, A., Sar?gün, Y., & Çavdar, U. (2016). Effect of Ekabor 2 powder on the mechanical properties of pure iron powder metal compacts. Revista de Metalurgia, 52(3), e073. https://doi.org/10.3989/revmetalm.073

Bouarour, B., Keddam, M., Allaoui, O., & Azouani, O. (2014). Boriding kinetics of C35 steel: estimation of boron activation energy and the mass gain. Metallurgical Research & Technology, 111(2), 67–73. http://doi.org/10.1051/metal/2014015

Çavdar, U., Ünlü, B. S., P?nar, A. M., & Atík, E. (2015). Mechanical properties of heat treated iron based compacts. Materials in Engineering, 65, 312–317. https://doi.org/10.1016/j.matdes.2014.09.015

De Almeida, E. A. dos S., Krelling, A. P., Milan, J. C. G., & da Costa, C. E. (2018). Micro-abrasive wear mechanisms of P/M AISI M2 steel with different surface treatments. Surface and Coatings Technology, 333, 238–246. https://doi.org/10.1016/j.surfcoat.2017.10.020

Dong, X., Hu, J., Huang, Z., Wang, H., Gao, R., & Guo, Z. (2009). Microstructure and properties of boronizing layer of Fe-based powder metallurgy compacts prepared by boronizing and sintering simultaneously. Science of Sintering, 41(2), 199–207. https://doi.org/10.2298/SOS0902199D

Erdogan, A., Kursuncu, B., Günen, A., Kalkandelen, M., & Gok, M. S. (2020). A new approach to sintering and boriding of steels “Boro-sintering”: Formation, microstructure and wear behaviors. Surface and Coatings Technology, 386(February), 125482. https://doi.org/10.1016/j.surfcoat.2020.125482

Fang, H., Xu, F., & Zhang, G. (2020). Investigation of Dry Sliding Wear Behavior of Pack Boriding Fe-Based Powder Metallurgy. Integrated Ferroelectrics, 208(1), 67–82. https://doi.org/10.1080/10584587.2020.1728717

Kare, D., Shoba, C., Dora, S. P., & Swain, P. K. (2021). Damping characteristics of pure aluminum: A comparison of microwave and conventional sintering. Metal Powder Report, 76(6), 22–25. https://doi.org/10.1016/s0026-0657(21)00299-x

Kayal?, Y., & Yönetken, A. (2021). Investigation of Wear Behavior of Borided Materials Produced by the Powder Metallurgy Method in Different Compositions. Protection of Metals and Physical Chemistry of Surfaces, 57(4), 771–778. https://doi.org/10.1134/S2070205121040122

Keddam, M., & Chentouf, S. M. (2005). A diffusion model for describing the bilayer growth (FeB/Fe2B) during the iron powder-pack boriding. Applied Surface Science, 252(1), 393–399. https://doi.org/10.1016/j.apsusc.2005.01.016

Koç, V. (2020). Effect of boro-sintering process on mechanical properties and wear behaviour of low alloy steel produced by powder metallurgy. Materials Research Express, 6(12), 1265c3. https://doi.org/10.1088/2053-1591/ab636b

Ozbek, I., & Bindal, C. (2002). Mechanical properties of boronized AISI W4 steel. Surface and Coatings Technology, 154(1-4), 13-17. https://doi.org/10.1016/s0257-8972(01)01409-8

Özdemir, O., Omar, M. A., Usta, M., Zeytin, S., Bindal, C., & Üç???k, A. H. (2009). An investigation on boriding kinetics of AISI 316 stainless steel. Vacuum, 83(1), 175–179. https://doi.org/10.1016/j.vacuum.2008.03.026

Šalak, A., Selecka, M., Vasilko, K., & Danninger, H. (2008). Face Turning of PM Steels: Effect of Porosity and Carbon Level. International Journal of Powder Metallurgy, 44(3), 49–61.

Sinha, A. K. (1991). Boriding. Journal of Heat Treating, 4(4), 437–447.

Turgut, S., & Günen, A. (2020). Mechanical Properties and Corrosion Resistance of Borosintered Distaloy Steels. Journal of Materials Engineering and Performance, 29(11), 6997–7010. https://doi.org/10.1007/s11665-020-05186-x

Y?lmaz, S. S., & Varol, R. (2010). The effect of surface hardening treatments on the mechanical properties of iron based P/M specimens. Powder Technology, 204(2–3), 236–240. https://doi.org/10.1016/j.powtec.2010.08.007

Downloads

Publicado

2025-08-29

Como Citar

Ertürk, L., & Selçuk , B. (2025). Investigation of The Effect of Borosintering Process on Various Properties of Iron-Based Materials . Acta Scientiarum. Technology, 47(1), e73252. https://doi.org/10.4025/actascitechnol.v47i1.73252

Edição

Seção

Engenharia Mecânica

 

0.8
2019CiteScore
 
 
36th percentile
Powered by  Scopus

 

 

0.8
2019CiteScore
 
 
36th percentile
Powered by  Scopus